Original
By certification 
Introduction
After decades of innovative development, our D Head Nail Making Machine adopts advanced European technology, the quality of the equipment is stable and reliable, eliminating the quality problems of long nails, short nails, machine heads, bent caps, different size nail caps and bent nails. It is easy to operate, low energy consumption and effective cost.
With the super high quality and high precision of our D Head Nail Making Machine, these models of nailers are suitable for different fields and always meet the needs of customers. All our machines used for manufacturing different models of nailers are covered by the corresponding warranties and can provide smooth service to our customers without any technical defects.
Advantage
The D Head Nail Making Machine has a square guide pillar structure in the middle, which effectively ensures performance and stability. The production of D-head nails, commonly known as paper strip nails, can perfectly solve the problems of length and burr. It can greatly improve the service life of the tool and other wearable parts without mishandling.
Specification
MODEL |
FFI-ZDJ-D90 |
Maximum Nail Diameter |
3.5mm |
Minimum Nail Diameter |
2.0mm |
Maximum Nail Length |
90mm |
Minimum Nail Length |
45mm |
Nail Making Speed |
680pcs/min |
Rated Power |
7kw |
Dimensions |
1350mm*1220mm*1050mm |
Machine Weight |
2200kg |
Common Faults and Solutions
Fault phenomenon |
Reason |
Solution |
Uneven length of nails |
The nail cutter is blunt and has serious burrs |
Change the nail cutter |
Wire feeding click tooth surface gaps, 6mm adjustable bolt is pressed too closely |
Adjust 6mm bolt upper side |
|
Click for wire back is too skew, Four pieces of alloy have worn out |
Inspect and change |
|
Feeder is not going well |
Tidy up the feeder |
|
The feed nozzle is blocked |
Clean the feed nozzle |
|
Vice punch is out of the potholes and uneven |
Take off and grind the punch |
|
Clamp flat of nail shaft |
Belt is misaligned |
Adjust belt slider |
ring – shaped groove of nail dies isn't chamfered |
Check and adjust in time |
|
Bending wire not corrected |
||
The upper guide pillar is too tight and prevents belt from running |
Loosen the screw, move up guide rail so that there are gaps between belts |
|
Different sizes of nail heads |
thermal expansion and cold shrinkage |
|
Vice punch is out of the potholes and uneven |
Take off and grind the punch |
|
Scissor is blunt and has serious burrs |
Change the scissor |
|
Out-of-round nail head |
The nail die is broken |
Change the nail die |
Large clamping gap of nail dies |
Repair nail dies |
|
Wrong net angle |
Repair net |
|
Bald head |
||
There are stairs of nail heads |
The nail head is out of round |
|
The right size |
||
Double heads |
Adjust the vice punch to make nail head plump |
|
Obvious camber in the clamp mark |
Misalignment of belt and nail mold center |
Adjust in time and check frequently |
Stop |
Lack of material |
Rethread |
Wire knotted |
Organize wires |
|
Lack of nail |
Check the wire feed clip, press the start button after inching the probe |
|
Blockage of nails |
Check nail bucket |
|
Inverter protection |
Press the STOP button at the bottom right corner of the inverter |
|
wire feed slider overheating protection |
Oil pump is short of oil, refuel in time |
|
the electric cabinet light is on, the motor doesn't run |
With the punch against the nail, turn the manual wheel to turn the punch past the highest point |
|
Lack of material |
Rethread |
|
Can't turn on the machine |
Manual wheel is not pulled out, electrical protection |
Pull out the manual wheel |
Site requirements
The height of the workshop is more than 2.5 meters, the length is more than 22 meters, and the width is more than 6 meters (installed side by side). The above includes raw material storage, from production equipment to finished product, sorting, packaging, and storage.
Finished Product
Our After-Sale Service
● Make a response to customers' inquiries or requirements within 12 hours.
● Assist customers to choose the most suitable machine, give them professional suggestions.
● Schedule machine production by our skilled team according to customers' demands.
● Offer customers manual instruction or video for machines to help them operate machines correctly.
● Provide customer layout of the workshop with a machine to help them complete the machine installation.
● Assign engineer to assist the customer to install machine if necessary.
● Offer one year guarantee for a concrete nail-making machine.
● Offer spare parts to customers no matter whether in guarantee or not as soon as we get feedback from customers.
http://www.finefasteners.com/
